Chief Manufacturing Stud Sensor CTA 2536 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
CTA-2536  
Internal Dual Stud Wall Plate  
The CTA-2536 Dual Stud Wall Plate provides a  
mounting solution for the following wall arms:  
CTA-025 Single Stud Wall Arm  
WMA-300 Wall Mount Arm  
The CTA-2536 has a maximum weight capacity of  
150 lbs. (68.0 kg).  
CTA-2536 Internal Dual Stud Wall Plate  
BEFORE YOU BEGIN  
CAUTION: To prevent damage to your equipment, which could affect or void the Factory warranty,  
thoroughly study all instructions and illustrations before you begin to install the CTA-2536. Pay particular  
attention to the Warnings and Cautions in this document.  
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.  
CHIEF MANUFACTURING INC.  
8809-000028 (Rev. A)  
2004 Chief Manufacturing  
11/04  
1-800-582-6480 952-894-6280 FAX 952-894-6918  
8401 EAGLE CREEK PARKWAY, STE. 700  
SAVAGE, MINNESOTA 55378 USA  
 
Installation Instructions  
CTA-2536  
CONTENTS  
INSPECT THE UNIT BEFORE  
PARTS ..............................................................................2  
INSPECT THE UNIT BEFORE INSTALLING ..............3  
TOOLS REQUIRED FOR INSTALLATION..................3  
INSTRUCTIONS..............................................................4  
Determine a Suitable Mounting Location .....................4  
Installing the Wall Plate ................................................4  
Attaching Wall Arm to Wall Plate ................................5  
Attaching Front Cover...................................................5  
Connecting NPT Pipe or Nipple to Wall Arm...............5  
INSTALLING  
Unpack the carton. Carefully inspect the parts for  
shipping damage. Verify contents listed in Table 1.  
If you are missing any of the listed parts, contact  
Customer Service at: 1-800/582-6480.300.  
Table 1. Shipping Contents  
ITEM DESCRIPTION  
QTY  
10  
20  
30  
40  
50  
60  
70  
Wall Plate  
1
6
6
6
6
6
1
5/16 X 2.5” Lag Bolt  
5/16 Flat Washer  
M8 Flat Washer  
M8 Lock Washer  
M8 X 16mm Button Head Cap Screw  
M5 Allen Key  
TOOLS REQUIRED FOR  
INSTALLATION  
The tools required for installation are as follows:  
Electric drill and bit set  
Stud sensor (mechanical or electronic)  
½” box-end wrench or ratchet with ½” socket  
13mm box-end wrench or ratchet with 13mm socket  
Level  
NOTE: Other tools may be required depending on  
your method of installation.  
3
 
Installation Instructions  
CTA-2536  
INSTRUCTIONS  
STEP 1  
Determine a Suitable Mounting Location  
NOTE: The wall plate (10) must be mounted to  
wood studs that are 16” apart on center.  
See Figure 2.  
16”  
1. Locate the wall plate (10), six lag bolts (20) and  
six flat washers (30).  
WARNING  
It is the installer’s responsibility to verify that the  
structure to which the mount is anchored will  
safely support five times the combined load of all  
attached components and equipment.  
2. Determine a suitable mounting location. Keep in  
mind that the wall plate (10) must be mounted to  
wood studs that are 16” apart on center.  
3. Using a stud sensor, locate the two wood studs  
where you will mount the wall plate (10).  
STEP 2  
Installing the Wall Plate  
Figure 2. Install the Wall Plate  
1. Holding the wall plate (10) against the wall, use a  
pencil, awl, or small nail to mark the mounting  
holes where the top two pilot holes will be drilled  
into the center of the wood studs. Make sure that  
the mounting holes in the unit are level.  
2. Using a 15/64” drill bit, drill two pilot holes for  
anchoring the wall plate (10). See Figure 2.  
3. Using two 5/16” lag bolts (20) and two 5/16” flat  
washers (30), fasten the wall plate (10) to the  
wall. See Figure 2.  
4. Repeat step 2 to drill four more pilot holes into  
the wood studs for the middle and bottom  
mounting holes.  
5. Repeat step 3 to install the remaining four 5/16”  
lag bolts (20) and four 5/16” flat washers (30)  
into the wood studs and to secure the wall plate  
(10).  
4
 
Installation Instructions  
CTA-2536  
STEP 3  
Attaching Wall Arm to Wall Plate  
1. Locate the wall arm, six M8 flat washers (40),  
six M8 lock washers (50), and six M8 x 16mm  
button head screws (60). See Figure 3.  
2. Attach wall arm to wall plate (10) as follows:  
a. Using the parts (40, 50, and 60) described in  
step 1 in the top mounting holes, attach the  
wall arm to the wall plate (10).  
b. Using the parts (40, 50, and 60) described in  
step 1 in the bottom mounting holes, attach  
the wall arm to the wall plate (10).  
Figure 3. Attach Wall Arm to Wall Plate  
c. Using the M5 Allen key (70), tighten the six  
M8 x 16mm button head screws (60) to  
secure the wall arm to the wall plate (10).  
STEP 4 [REFERENCE ONLY]  
Attaching Front Cover  
1. Locate front cover and four M4 x 8mm Phillips  
head cap screws (shipped with wall arm).  
NOTES  
The front cover may be partially removed  
and reinstalled to conceal power/audio/video  
cables after the TV/Mount is installed.  
You may remove one or both knockouts on  
cover to assist routing to wall through cover.  
Figure 4. Install Cover on Wall Arm  
2. Install the front cover using four M4 8mm  
Phillips head cap screws. See Figure 4.  
STEP 5 [REFERENCE ONLY]  
Connecting NPT Pipe or Nipple to Wall Arm  
1. Locate M6 x 6mm set screw and 1-1/2” NPT  
pipe or nipple (supplied with TV Mount or  
purchased separately).  
2. Connect the 1-1/2” NPT pipe or nipple (supplied  
with TV Mount or purchased separately) to the  
wall arm. See Figure 5.  
3. Using the M3 Allen key, install the M6 x 6mm  
set screw. Tighten the set screw.  
(Supplied with TV Mount  
or purchased separately)  
WARNING  
Make sure to tighten the M6 x 6mm set screw to  
prevent equipment damage or personal injury.  
Figure 5. Connect NPT Pipe or Nipple  
to Wall Arm  
5
 
 

Bernina Sewing Machine Stitch Regulator User Manual
Black Decker Rice Cooker RC1820 User Manual
Bose DVD Player AM259777 User Manual
Brinkmann Gas Grill ProSeries 4675 User Manual
Brinly Hardy Lawn Mower Accessory SAT 400 BH User Manual
Carrier Access Network Router Access Navigator User Manual
Casio Watch QW 1444 User Manual
CDA Cooktop HCC662 User Manual
Chamberlain Garage Door Opener 1000SDC R, 2000SDC R User Manual
Cisco Systems Modem 4013371 User Manual